Trying to install your new garage door? Refrain from losing patience. At first, installing a garage door might seem difficult, but with time, patience, and the assistance of a friend, it won’t be too challenging. We’ll walk you through the process and describe the nuances involved.
Is It Challenging To Install A Manual Garage Door?
A garage door can be more difficult to install than a regular door. It can be risky as well as challenging. A manual door is much lighter and requires no motor or cables, making it much simpler to install than an automatic one. However, it will need to be automatic if you find a solid wood door or another heavy door that you really love.
As a result of having fewer parts, manual garage doors are not only simpler to install but are also frequently more secure. Automatic garage doors use radio-operated motors, which are susceptible to hijacking by anyone with a low-cost gadget that “sniffs” out the frequency of the door motor. While an automatic door will stop closing and open instead if something is in the way of its closing, this means someone can place something in the way of the door and prevent it from closing, making it simple for them to enter your home. Finally, manual garage doors require a key to open, which makes them challenging to break into.
How To Install A Garage Door
The necessary tools must be gathered, and you must follow the manufacturer’s installation instructions, for a secure installation of your new garage door. Get the following tools and supplies in advance of installing your garage door:
- Level
- Safety glasses
- Adjustable-locking pliers
- Drill
- Drillbits
- Socket bit
- Phillips driver bit
- Open-ended wrench
- Hammer
- 1/2-inch diameter rods
Follow these 10 easy steps to install your new sectional garage door once you’ve gathered the necessary tools. Installing sectional garage doors involves putting each section in one at a time, working your way up from the bottom. Sectional garage doors are the most popular kind of residential garage doors, with three to eight panels that slide up and down along a track.
Read More to learn the following information about door fix!
- Why Won’t Your Garage Door Close – Reasons & 3 Ways to Close
- How to Remove Shower Doors and Patch the Holes Left in the Tile?
- How to Replace a Door Frame with Simple Steps
- How to Fix Pocket Door Scratching – Perfect Solutions
- Why Put Foil On Door Knob When Alone – Is It Necessary?
- How To Fix Garage Door Cable? A Complete Guide For You
- How To Fix A Door That Won’t Latch?
Release The Garage Door Tension
Since garage door springs are under a lot of weight and tension in this first step, you should proceed with the utmost caution. They can result in property damage and personal injury if handled improperly. You must first release the torsion spring’s tension before working on the garage door. Here are the steps to accomplish this:
- Utilizing your adjustable-locking pliers, clamp the torsion spring shaft before pressing your pliers up against the header wall above the garage door.
- The spring winding cone, which stretches and contracts the spring, has four holes that you can see. One of the holes should be filled with a steel rod. Loosen the screws holding the winding cone in place while maintaining a firm grip on the rod.
- By switching the two rods, loosen each spring by a quarter at a time. Turn the cone with the other rod while holding it steady with the first one.
Disconnect The Current Door From The Garage Door Opener
You can now unplug your garage door from the opener after releasing the garage door’s tension. The red emergency release handle must be pulled in order to safely disconnect the door. This will position the trolley arm vertically, enabling you to manually raise or lower the door.
You can start taking out the sectional door panels at this point:
- Remove the hinges holding the garage door panel to the panel, starting at the top.
- By releasing the doorframe bolts, you can detach the panel from the track.
- Continue taking off the hinges from each panel and releasing the sectional panels’ hardware.
Install The Sectional Garage Door Panels
Finally, you can start installing your new garage door. In order to prevent bowing in the middle when replacing a two-car garage door, add a strengthening bar along the top panel. Then, if the manufacturer hasn’t already done so, drill pilot holes and use screws to fasten the bar to the panel. Start by:
- Attaching the hinges to the top of each garage door panel
- Attaching axle supports to the bottom and top panels
- Placing the bottom panel into the opening and checking that it’s level
- Place each new panel over the one beneath it, making sure the upper panel’s groove is properly positioned on the lower panel’s ridge. Continue doing this until every panel is securely in place.
Secure Hinges And Install The Tracks
The wheeled axles are inserted into the side hinges, the top and bottom axle supports are installed, and the top half of each hinge is securely fastened to the panel above it. To ensure proper operation, install the track after checking that the wheels are positioned correctly in it. The bottom bracket should then be fastened to the wall after the door cable has been attached to the hook on the panel axle support.
Attach Spring Assembly To The Track
Put together all the parts that hold the spring and connect to the track at this time. Place the curved portion of the track on the vertical piece you previously created, using the ceiling supports from the previous door as support. the other end to the ceiling bracket and secure it there.
Bolt The Tracks Together
To attach to the door, align your horizontal and vertical tracks, then bolt them together.
Install Springs
Securely bolt the two springs to the header bracket after connecting the spring anchors to the springs and adding the spring locking cone.
Install Torsion Rod And Pulleys
Pulleys should be attached to each end of the torsion rod after it has been slid into the side header brackets’ holes for installation.
Attach Cable
To pull any slack taut over the pulley, fasten the cable to the pulley wheel from below and turn the wheel. In order to secure all components, slide the wheel onto the header bracket. As you tighten the garage door springs, prevent the rod from spinning by fastening a pair of locking pliers to the rod that is on the outside of the bracket.
Tighten Springs
Tighten the springs with the steel rods you have and consult your owner’s manual to learn how many turns are likely necessary to do it right. The pliers should be taken off the torsion rod once the spring has been tightened to the proper tension. Tighten all bolts to secure the spring in place.
Conclusion
You can install the garage door yourself if you follow the above instructions. As you may have guessed, though, installing a garage door can be a challenging task to take on by yourself, particularly if you don’t have the necessary training and expertise to carry out this project securely. Calling in a professional garage door installation company can help you avoid many headaches, both big and small if you are unsure about your ability to install your garage door safely and without error. A few justifications for hiring a pro to install your garage door include: